Subsonic cartridges do produce less noise than full-velocity rounds, but there’s no free lunch-as usual. The label on the ammo box says subsonic, so this stuff won’t spook every deer in the county like your earth-shattering aught-six does, right? Well, sort of. Wait til you see how much fun it is to make all of your own ammo and never buy factory ammo again.We may earn revenue from the products available on this page and participate in affiliate programs. You only need to spend a few moments in this forum clicking topics, seeing folks ask questions (running the gamut from basic to deeply involved) and then look at all the folks willing to respond with their experiences and ideas. With the round apart, you can get a proper visual on how a heeled bullet works and why you likely can't get anywhere with this idea.Ģ) Handloading is not at all difficult! And it's outrageously rewarding and most of us that do it. 22LR right now and a pair of pliers and grab (only) the bullet and rock it back and forth in the brass and get it out of there. However, there's at least two things you can take away from this conversation!ġ) Grab a round of. Your plan/idea is, for all but the most extremely able (with expensive tools and a well outfitted work shop) impossible. Handloaders can manipulate these center fire rounds because we have the tools to do so and at the heart of all the tools we use are very simple reloading dies, basically just tool steel that we can run the brass and bullets up inside and impart pressure upon the components.Īs far as I know, you can't even purchase such dies for. 22LR ammo will result in either a messed up cartridge case (that you'd need to fix upon reconstruction!) or a very messed up soft lead bullet that would absolutely affect it's flight/accuracy. you have to wildly abuse either the cartridge case or the rounded heel of the bullet itself.Īt the very least, even attempting to break down. 17) is fairly straightforward and is done with no damage to the bullet and no damage to the case. This means that removing a bullet from a center fire (or. 22LR - the bearing surface of the bullet actually sits on top of the cartridge case and the cartridge case itself is the same or slightly under the bore diameter. 17HMR for that matter) use a standard bullet inside the cartridge case and with. The heeled bullet design is the one last holdover from a bygone era. Rimfire does not lend itself well to the force we must apply to it. it's also a bit of an issue in the manner that our equipment physically handles and manipulates the brass cartridge case. The rimfire priming is such that not only is (basically, for all intents and purposes) impossible for us to do or re-do. There are two main things - the heeled bullet design and the rimfire priming. 22LR rimfire (that matters from a handloading or reloading) standpoint is far, far more difficult an non-feasible than any/all/every centerfire round. I don't know squat about suppressors so I will stay out of that area of the discussion but I am a long time, hardcore hobbyist handloader.Įverything about. Personally, if I thought the bullets could be safely re-seated in the case, I'd look at this as a challenge which might lead me to try reloading centerfire ammo If it were safe, I was thinking I could pull bullets from 100 rounds (or more), dump all the powder, weight it, reduce by some percentage, measure the new amount, and reload the bullets. Would it be feasible to take existing 22 SV or HV plated rounds, remove the bullet, and reduce the powder load to a subsonic level? I’ve seen countless threads about the difficulty of priming rimfire rounds, but how difficult would it be to remove the bullet, reduce the powder, and replace the bullet? And would you be able to seat the bullet safely, especially considering you’ll be using a suppressor with baffles? I’ve researched plating LRN subsonic rounds, sort of like you see with old Russian copper-washed rounds, but that appears unfeasible in a non-commercial setting. There are a few subsonic, plated 22 rounds manufactured, but after 3 months of searching almost daily, I have yet to find any actually for sale or in stock. Likewise, firing plated rimfire ammo is much cleaner for the barrel and the suppressor. From my research, the lead/carbon fouling you get in a rimfire suppressor from LRN or lead hollowpoints is very difficult to clean. I have a rimfire suppressor on hold awaiting approval by the ATF. I’ve been a shooter for decades but have never considered reloading, so I’m wondering if my idea is feasible.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |